FAG Self Aligning Ball Bearing Got Misalignment? Try These 5

The 1200 series, 1300 series, 2200 series, 2300 series, and 11200 wide series lead the FAG self aligning ball bearing lineup for misalignment. Each self-aligning ball bearing uses a concave outer-ring raceway and two ball tracks. These double-row bearings absorb shaft deflection and angular misalignment under radial and moderate axial load. The design suits industrial machinery, and the bearings deliver reliability in demanding equipment. Self-aligning ball bearings serve many industrial applications. These rolling bearings and other FAG bearings vary by speed, environment, and budget. Each model follows.

Key Takeaways

• Each FAG self-aligning ball bearing series targets specific needs: 1200 for light loads, 1300 for higher radial capacity, 2200 for sealed protection, 2300 for heavy loads, and 11200 for shaft deflection.
• Match bore size, load type, speed, and environment to choose the right bearing and ensure reliable machinery performance.
• Consult a bearing specialist if misalignment continues after correct installation to maintain equipment reliability.

FAG 1200 Series for Light-Load Misalignment

Technical Specifications

The 1200 series is the smallest of the five fag self aligning ball bearing families. The 1200-TVH model carries a 10 mm bore, a 30 mm outer diameter, and a 9 mm width. Its basic dynamic radial load rating reaches 5700 N, and its static rating sits at 1180 N. Limiting speed runs up to 29500 rpm, according to hsnbearings.com. These double-row bearings come in P0, P6, and P5 precision grades with brass or steel cages.

Application Fit

These self-aligning ball bearings suit light-load positions where shafts flex. Common applications include marine deck machinery, conveyors, and agricultural equipment, per hiqool.com. Conveyor frames bend under load, so continuous misalignment occurs. Hay baler rollers and grain auger drives also benefit. Fan and pump drive shafts in industrial machinery rank among the typical uses.

Regulatory Compliance

The 1200 series meets DIN 630, and manufacturers supply it with ISO9001:2015 certification. These standards support reliability in industrial equipment.

Cost Considerations

The 1200 series ranks as the most economical option in the lineup. Small bore sizes keep unit prices low. Buyers should weigh load capacity against budget before choosing this model for motor applications.

FAG 1300 Series for Higher Radial Capacity

Technical Specifications

The 1300 series raises radial capacity well above the 1200 line. A representative 1317-M fag self aligning ball bearing from MRO Supply carries an 85 mm bore, a 180 mm outer diameter, and a 41 mm width. Its basic dynamic radial load rating reaches 99000 N, and its static rating sits at 37500 N. Limiting speed runs at 5600 rpm, and the brass cage supports temperatures from -30 to +150°C.

Application Fit

These self-aligning ball bearings handle heavier radial load in industrial machinery. Gearbox shafts, heavy conveyors, and crusher drives rely on this extra bearing capacity. The self-aligning action still absorbs shaft deflection in these applications.

Regulatory Compliance

The 1300 series meets DIN 630, and FAG supplies each unit with ISO9001:2015 certification. These standards support reliability across industrial equipment.

Cost Considerations

Lager-Techniek lists the 1303-TVH at 21.57 EUR, against 31.49 EUR for the SKF 1303ETN9 and 18.85 EUR for the NSK 1303TNG. Larger sizes narrow the gap: the 1309-TVH sells for $171.96, close to the SKF 1309 ETN9 at $171.11. Lager-Techniek notes that self-aligning ball bearings typically cost 10–30% more than standard deep-groove ball bearings of the same size.

FAG 2200 Series for Sealed Industrial Applications

Technical Specifications

The 2200 series adds double seals (2RS) to the self-aligning ball bearings design. A representative 2200-2RS-TVH unit uses a 10 mm bore and a 30 mm outer diameter. The seals block dirt and moisture, so the bearing holds lubricant longer in dusty plants. A double-row self-aligning ball bearing in this series typically carries 1.5× to 1.8× more load than an equivalent single-row 1200-series unit of the same bore, according to SKF, NSK, and Timken load rating comparison tables. The self-aligning action tolerates angular misalignment up to 3 degrees, per MRO Supply.

Application Fit

Sealed 2200 units fit environments where contamination shortens bearing life. MRO Supply lists three main settings:

• Industrial machinery in manufacturing plants, conveyor systems, and agricultural equipment
• Automotive components such as transmissions, differentials, and wheel hubs
• Light to medium duty operations that demand reduced maintenance

Heavy conveyor drives, idler rollers, and high-capacity machinery with compact housing design also suit this fag self aligning ball bearing. The sealed rolling bearings cut re-alignment frequency in high-vibration positions.

Regulatory Compliance

The 2200 series follows DIN 630 dimensioning and carries ISO9001:2015 certification. These standards support reliability in industrial equipment.

Cost Considerations

Lever-es.com lists the 2200-TVH open version at £19.25, reduced to £16.04, with a 1–3 day lead time. ABF.store quotes the sealed 2200-2RS-TVH on request. Sealed units cost more than open types, yet they lower downtime in dirty industrial applications.

FAG 2300 Series for Heavier Radial Loads

Technical Specifications

The 2300 series widens the bore range and raises radial capacity for heavy load positions. MRO Supply lists the 2309-2RS-TV with a 45 mm bore, a 100 mm outer diameter, and a 36 mm width. Its dynamic radial rating reaches 38500 N, and its static rating sits at 12600 N. The 2311K-TV-C3 steps up to a 55 mm bore and a 120 mm outer diameter. That unit carries a 77000 N dynamic rating and a 23800 N static rating.

Application Fit

These double-row bearings serve heavy machinery such as crushers, mixers, and large gearbox shafts. The self-aligning action absorbs deflection while the higher load rating carries the weight. Plants choose this fag self aligning ball bearing for heavy-duty industrial applications where standard ball bearings fall short.

Regulatory Compliance

The 2300 series follows DIN 630 dimensioning and ships with ISO9001:2015 certification. These standards support reliability in industrial machinery.

Cost Considerations

Lager-Techniek lists the 2304-TVH at 30.95 EUR, down from 52.05 EUR. MRO Supply quotes the sealed 2304.2RS.TV at $70.27 each. Sealed versions cost more, yet they extend service life in dusty equipment. Buyers should weigh this premium against downtime during heavy-duty bearing selection.

FAG 11200 Wide Series for Shaft Deflection

Technical Specifications

The 11200 wide series extends the inner ring beyond the standard width. A representative 11204-TVH unit carries a 20 mm bore, a 47 mm outer diameter, and a 40 mm width. The extra width spreads contact stress along the shaft and resists deflection at higher shaft speed. Dynamic radial ratings reach roughly 12700 N, and static ratings sit near 3200 N. These self-aligning ball bearings tolerate angular misalignment up to 3 degrees.

Application Fit

The wide inner ring suits long shafts that bend under load. Conveyor head pulleys, line shafts, and fan drives in industrial machinery rely on this design. Textile machinery and printing equipment also benefit. These ball bearings absorb deflection without extra housing space, so plants gain reliability in heavy-duty applications.

Regulatory Compliance

The 11200 series follows DIN 630 dimensioning and ships with ISO9001:2015 certification. These standards support dependable performance in industrial applications.

Cost Considerations

Wide-series bearings cost more than standard 1200 units of the same bore. The premium buys longer service life on flexing shafts. Buyers should compare total downtime against unit price before selecting this model for heavy machinery.

Quick Comparison: Which Ball Bearing Fits Your Application?

Comparison Table: Load, Speed, Misalignment, and Cost

The table below summarizes the key selection factors across all five FAG self-aligning ball bearing families. Buyers can compare load rating, speed limits, misalignment tolerance, and relative cost at a glance.

Best-Fit Summary by Industry

Each industry pairs best with a specific series. The 1200 series suits conveyors and agricultural equipment. The 1300 series fits gearbox shafts and crusher drives in industrial machinery. The 2200 sealed units serve dusty manufacturing plants and automotive components. The 2300 series handles crushers, mixers, and large gearbox shafts in heavy-duty applications. The 11200 wide series works well for line shafts and fan drives.

These ball bearings share a common self-aligning design. The right pick depends on load, speed, environment, and budget. A bearing specialist can confirm the final choice for demanding industrial equipment. Proper selection supports reliability across industrial bearing solutions and keeps machinery running.

The 1200 series suits light-load positions, the 1300 series handles higher radial capacity, the 2200 series fits sealed industrial applications, the 2300 series carries heavy radial loads, and the 11200 wide series resists shaft deflection. Match bore size, load type, speed, and environment before finalizing any selection. Consult a bearing specialist when misalignment persists after correct installation. These ball bearings support machinery reliability across demanding equipment.

FAQ

How much misalignment do FAG self-aligning ball bearings tolerate?

Most FAG self-aligning ball bearings accept angular misalignment up to 3 degrees. The concave outer-ring raceway allows this movement. Larger deflection demands a different bearing design.

Do sealed 2200 series bearings suit dusty plants?

Yes. The 2RS seals block dirt and moisture, so lubricant stays inside longer. These bearings cut maintenance in dusty industrial applications. Plants gain reliability and longer service intervals.

When should a buyer upgrade from the 1200 to the 2300 series?

A buyer upgrades when radial loads exceed the 1200 rating. The 2300 series carries heavier loads in crushers and mixers. Match load data before selecting equipment bearings.